I think this link is broken it redirects me to this page doesn’t give any download ^^ “Validity Sensor Driver Compaq Presario CQ40 Windows 7 x64 (64-bit)”. Template Per Microsoft Expression Web there. Windows 7 Drivers for Compaq Presario CQ40 SeriesOS: Windows 7 32-bitServer: Hewlett PackardDriver-Audio (2):IDT High Definition Audio CODEC Version 6.10.6225.0 Rev.

• I have a compaq presario cq60 and I want to restore it to factory settings. I continually press F11 when I turn it on but nothing happens except windows starts normally.
• On this website you will find information about all main parts inside a typical laptop or notebook computer. You can identify parts by the description or image below.
• Create Custom Windows XP CD with SATA Drivers Written on December 10th 2010 at 12:21. Last modified: August 26, 2011.

Load SATA Drivers On Your Windows XP Setup CD.

How to replace screen on HP G5. G6. 0 G7. 0In the following guide I explain how to remove and replace damaged LCD screen on HP G5. G6. 0/G7. 0 notebooks. I’m replacing it on a HP G5. HP G6. 0 and G7. 0. By the way, HP G5.

G6. 0/G7. 0 models also known as Compaq Presario CQ5. Presario CQ6. 0 and Presario CQ7. In most notebooks you can replace the screen without separating the display panel from the base but not in HP G5.

G6. 0/G7. 0. In these models we’ll have to remove display panel first. By the way, in the next post I show how to remove the motherboard. You can find the HP spare part number in the service manual. I linked to service manuals at the end of this guide. STEP 1. Turn off the laptop and remove the battery. Remove one screw securing the Wi- Fi cover and remove the cover.

It is not necessary to remove the memory and hard drive covers. I marked them just for your convenience. STEP 2. Remove three (yellow) screws securing the keyboard. Remove four (red) screws securing the keyboard cover. If you are using this guide for replacing the keyboard, you have to remove only three (yellow) screws. In G5. 0 and G6. 0 the keyboard screws are located in the battery compartment. In G7. 0 notebooks there are only two screws securing the keyboard and they are located on the bottom (there is a small keyboard stamped close to each screw).

STEP 3. Carefully lift up the keyboard from the base. STEP 4. Place the keyboard so you can access the cable connector underneath. You have to unlock the connector and release the cable before removing the keyboard. Move the white clip about 2- 3 millimeters towards the display panel and release the cable. Now you can remove the keyboard. WARNING! The white clip must stay attached to the connector base. If you accidentally break the connector, you’ll have to replace the motherboard.

If you work slowly, everything should be fine. On the picture below the connector is shown in the unlocked state. STEP 5. Disconnect the switch board cable from the motherboard. STEP 6. Remove the keyboard cover. Move the cover towards the display to separate from the top cover. STEP 7. Turn the laptop upside down and disconnect two antenna cables from the wireless card.

Each antenna cable has a golden head. Grab the head with your fingers and lift it up. STEP 8. Disconnect the video cable connector from the motherboard. Disconnect the webcam cable from the motherboard.

Pull two Wi- Fi antenna cables through the opening. STEP 9. Remove four screws securing the display panel hinges. STEP 1. 0. Lift up and separate the display panel from the base.

In the following steps we will disassemble the display panel and remove the LCD screen. STEP 1. 1. There are two screw seals located in the lower left and right corners. Remove these seals with a sharp object and remove screws found under the seals. STEP 1. 2. Start separating the bezel from the display cover. Continue separating the bezel. The bezel has been removed. STEP 1. 3. The inverter board is mounted on the bottom side of the display cover.

The inverter is locked between plastic brackets. You can remove and replace the inverter board without removing the screen. Simply pull the inverter board from the cover and disconnect connectors on both ends. STEP 1. 4. Remove two screws securing the right display hinge. Remove the right hinge. STEP 1. 5. Remove two screws securing the left display hinge.

Remove the left hinge. STEP 1. 6. Remove the inverter board from the cover and disconnect one connector from the right side. By the way, this is the backlight connector. STEP 1. 7. Remove two screws securing the mounting brackets on the top.

STEP 1. 8. Now you can separate the LCD screen from the display cover and access the video cable. My HP G5. 0 notebook didn’t have the webcam installed and the webcam cable was taped to the display cover. If you have a HP G6. G7. 0 notebook, most likely it came with the webcam. You’ll have to disconnect the cable from the webcam before disconnecting the video cable. STEP 1. 9. Remove sticky tape securing the video cable connector and unplug the video cable.

STEP 2. 0. Now you can remove the LCD screen from the cover. If you are replacing it, you’ll have to transfer the left and right mounting brackets to the new screen. Remove three screws securing the bracket and remove the bracket. Do the same with the other side.

The LCD screen model number is located on the sticker. In my laptop I had this model installed: B1. EW0. 8 v. 1. The HP part numbers for LCD screen and other parts can be found in service manuals and here they are. Service manual for HP G5. The Arden Shakespeare Complete Works Revised Edition Magic Cards. Compaq Presario CQ5.

Service manual for HP G6. Compaq Presario CQ6. Service manual for HP G7. Compaq Presario CQ7. You can support my work!

It takes hours to create one disassembly guide and only a minute to donate.